Know someone planning a yard project?
Watering time and watering coverage are different
Coverage describes where the water lands and how evenly it’s distributed. Run time describes how long the zone operates. A dry corner and a soaked center can occur in the same zone. Adding minutes may make the center wetter without resolving the corner.
Watch the sprinklers run. Look for blocked spray, heads that don't rise or rotate, water hitting paving and visible leaks. Note what happens in each zone before changing settings.
For a new lawn, check the system before installation. Fresh sod should not be the test that reveals an existing coverage problem.
Walk the lawn with the controller running one zone at a time

Choose conditions with little wind and follow local watering rules. Watch a complete operating cycle where practical. A rotor may need time to sweep its arc, while a fixed spray shows its pattern immediately.
Note the places where water lands outside the planted area. Check for plants blocking the spray and heads sitting below surrounding grass. Record bubbling, unusually weak patterns or a head that keeps draining after the zone has finished.
Don’t force adjustments on unfamiliar equipment or dig into buried connections to investigate. Photos and zone numbers help a qualified irrigation professional assess the issue.
Use measurements rather than the color of the lawn alone
Texas A&M AgriLife’s lawn-water guidance describes collecting sprinkler water in containers to measure application. A consistent test can show differences that are hard to judge by watching the spray.
Keep the test duration the same across the measured area, record locations and compare the collected amounts. A professional irrigation audit can evaluate distribution more systematically. Measurements are evidence about delivery, not a complete diagnosis of every brown patch.
For an illustrative example, readings of 0.10, 0.12, 0.24 and 0.26 inches average 0.18 inches. That average hides the fact that the wettest spot received more than twice the driest. Extending the cycle keeps the imbalance unless its cause is addressed.
Use these clues to ask better questions
| Observation | Possible issue to assess | Avoid assuming |
|---|---|---|
| Dry strip at an edge | Coverage limit, obstruction or head position. | That every dry strip needs extra fertilizer. |
| Weak spray across a zone | Pressure, flow, leaks or equipment compatibility. | That adding more heads will solve it. |
| Wet spot with normal surroundings | Leak, low area or concentrated delivery. | That the entire lawn needs less water. |
| Runoff before enough water is delivered | Application and soil intake mismatch. | That a longer uninterrupted cycle will help. |
| New gap after landscaping | Changed beds, turf area or blocked heads. | That the old layout still fits. |
These are possibilities, not diagnoses. Soil condition, shade and turf health also affect how a lawn responds.
Use the observed pattern to prepare for the repair visit: record leaks, dry patches and dead zones.
Fix delivery, then refine the schedule
Once the system operates properly, review timing against weather, soil moisture, grass needs and city restrictions. A controller schedule should not be copied unchanged from a neighbor’s yard.
Where runoff occurs, ask whether shorter cycles with soak time suit the site. Don’t turn that into a universal number of minutes: nozzle output and soil intake vary.
New sod and established grass have different establishment needs. Use our aftercare guide for rooting-based decisions and the city watering information. A watering exception, where available, must be confirmed with the city.
When a small fix may not be enough
A blocked or damaged head may call for a focused repair. A lawn that has changed shape, gained beds or lost a large planting area may need a broader layout review.
For artificial turf, discuss irrigation changes explicitly. Don’t leave a zone watering a surface that no longer needs lawn irrigation, and don’t disable water needed by nearby plants.
Our repair-versus-replacement guide helps frame that conversation. Ask what the planned work will correct and how it will be checked afterward.
Before new sod is scheduled, confirm that working irrigation covers the whole installation area. Plano Landscaping will NOT install new sod on lawns without irrigation. If irrigation is missing, discuss installation first; if coverage is uneven, assess repairs before laying sod.
Continue planning: compare North Texas grass varieties · review sod installation pricing · plan installation timing · read watering and aftercare guidance · discuss irrigation installation or repairs.
Bring a zone-by-zone record
- Controller model and current schedule.
- Photos of wet and dry areas, with zone numbers.
- Observed leaks, runoff and blocked spray.
- Recent changes to beds, paving or lawn.
- Any planned sod or turf installation.
TCEQ’s irrigation plan checklist illustrates why design and backflow details matter when work goes beyond observation. Ask the provider to confirm applicable qualifications and approvals; this article doesn’t claim a license for Plano Landscaping.
Request an Irrigation Assessment →Coverage questions
Should I just run the dry zone longer?
First determine whether delivery is uneven. Extra time can overwater areas already receiving enough.
Does brown grass prove poor coverage?
No. Check delivery alongside soil moisture, grass condition and other possible causes.
Can landscaping change coverage?
Yes. Changed planting areas and obstructions can make the old layout unsuitable.
Should coverage be checked before sod?
Yes. Identify needed repairs or adjustments while the site is being prepared.
Sources and limits
Reviewed October 4, 2026. Texas A&M AgriLife supports measurement-based irrigation management; TCEQ provides the linked plan checklist. The measurement example is hypothetical. This is a homeowner assessment guide, not an irrigation design or a prescribed watering schedule.
Know someone planning a yard project?

Compare artificial turf
Plan the new lawn



